Heat-shrink solder connector for extending connection cables: Connect - solder - insulate - seal - in one simple working process.
€2.99*
Available, delivery time: 1-3 days
Heat-shrink solder connector for extending connection cables:
Connect - solder - insulate - seal - in one simple working process.
Child's play! All done without a soldering iron or solder wire. The result is a watertight and more durable connection than with crimp connectors or screw terminals.
Scope of supply for eco+:
2 No. solder connectors
1 No. heat-shrink hose
Scope of supply for PRO²:
4 No. solder connectors
1 No. heat-shrink hose
Technical data:
Ingress protection type: IP67
Heat-shrink at: >110 C°
Temperature-resistance after shrinking: -45 °C to +125 °C
Length of solder connector: 40mm
Diameter 3mm, for cable cross-sections 0.5-0.75mm²
Instructions: Remove approximately 5 mm of insulation from the cables to be connected. Twist each of the bare cable ends and insert them, one from each side, until the ends lie parallel to one another under the silver ring (solder) in the middle of the connector. Heat the solder connector to approximately 110°C (it is best to use a hot-air gun, but it also can be done with care using a cigarette lighter etc.). The heat shrink sleeve reduces in diameter and sticks together, the solder melts completely and a watertight and very strong connection is produced. Hold the cable in position until the solder has cooled and become solid. The heat-shrink hose is transparent, which allows you to visually inspect the connection. Now shrink-on the supplied black heat-shrink hose around the whole connection for additional protection and to make it so the connection cannot be seen. AND THAT'S IT DONE.
Login
26 April 2019 15:42
Top!
einfach - unklompiziert - effektiv! Mehr muss hier nicht gesagt werden
14 August 2016 15:07
Tolle Qualität
4 October 2015 16:20
Coole Sache
Brauche bei diesen Teilen noch nicht einmal meinen Löter rauskramen, Heisluftpistole darangehalten und ruckzuck gelötet, dass bekommt echt jeder hin ;)
28 March 2023 07:51
Sehr einfach zu benutzen
Geniale Lösung
8 December 2023 22:11
gut
gut
20 February 2019 14:26
sehr gut
Es ist sehr einfach zu verarbeiten und funktioniert super. Kann ich nur empfehlen.
6 February 2016 12:29
gut
es ging nicht ganz so einfach wie erwartet, aber letztll ich hat es funktioniert
30 September 2015 14:26
Alles super
Super Service, gerne wieder.
24 February 2023 09:58
Kann ich nur empfehlen
Also das Produkt ist vom feinsten lässt sich sehr gut bearbeiten
3 September 2018 19:46
Gute Idee mit der bereits eingearbeiteten Löthülse.
Customers also bought
Heat-shrink solder connector for extending connection cables: Connect - solder - insulate - seal - in one simple working process.
Silicone hose for supplying the water cooling.
Silicone bow 180° for connecting flow and return.
High-performance LED switching mains adapter for operating our LED lighting bars (12V DC)
The CleanCover protects the LED bar from limescale and dirt deposits and is very easy to clean. A splashwater protection, made of highly transparent, ultra-thin, impact-resistant plastic.
Similar products
Heat-shrink solder connector for extending connection cables: Connect - solder - insulate - seal - in one simple working process.
This distributor allows several LED lighting bars to be operated with a single mains adapter (assuming the power output is adequate).
Adapters to connect LED lamps and, if necessary, mains adapters manufactured by third parties to our dimmers, light control and daylight simulation systems.
For connecting 2 LED bars or 2 temperature sensors to one channel of a light control.
