You receive a lighting system from us that is immediately ready for operation. All you have to do is connect the individual components and it will be bright! You don't need any special tools or expertise for this, just a screwdriver at the most. The further installation in your cover, a ceiling suspension or whatever your plan calls for is then in your hands. We supply the necessary accessories and instructions!
Here you can see your current selection:
These power supplies are necessary to operate the integrated moonlight of the powerBEAM LED luminaires. The moonlight of the 125 version has a power of 25W, that of the 240 version 40W. For a powerBEAM 125 a 35W power supply unit is sufficient. For a 240 a 100W power supply unit must already be selected. etc. The High Performance LED switching power supply is an extremely high-quality LED switching power supply that sets standards in quality and performance. Tip: Click on the article name or image to open the respective product description!
From the mains filter to the temperature sensor. These accessories are not mandatory, but can be useful depending on the project. The optional reflector restricts the beam angle of the luminaire from 110° to 90° if required. Tip: Click on the article name or image to open the respective product description!
Do you want your lighting control system to be ready to go right away? And exactly according to your ideas? Then the "Programming service" is exactly what you need! Tip: Click on the article name or image to open the respective product description!
Configuration of an individual combination of powerBEAM LED luminaires incl. all necessary and optional accessories.
What power output do I need? Please use our calculator to find out:
Power-supply-calculator | ||
---|---|---|
Model | Length/Variant | Quantity |
Power supply Too much for one power supply
|
This is how it works: The power that the mains adapter has to supply is calculated by adding the individual power ratings (watts) of the intended LED lighting bars and then adding a further min. 10% reserve. The correct mains adapter is then the next larger model. Always allow for a minimum 10% power reserve in order not to overload the mains adapter! (Our calculator takes this into account automatically!)
For the avoidance of any misunderstandings: The mains adapters themselves do not consume 30, 75 or 150W of power! But they are capable of delivering this power! Power consumption depends only on the connected LEDs and the efficiency of the mains adapter! In standby (i.e. when the power supply unit is only plugged into the socket, not connected to LEDs or in operation) the consumption is close to zero.
Yes, the LED bars are specifically designed to be installed in existing, enclosed covers. Due to their waterproof rating (IP67), they are suitable for moist aquarium covers but should not be placed directly underwater. Persistent dampness and deposits like lime and dirt may impair the quality and lifespan of the LED bars. Thus, we recommend using our special CleanCover to protect the LED bars. The LED bars cool passively through the ambient air, so adequate air circulation is crucial. In most cases, the existing openings for cables and hoses in the cover are sufficient for this purpose.
The differences between these products depend on your individual lighting needs. The aquaLUMix provides a compact and highly powerful solution with all the light colors needed for an appealing daylight simulation. It also includes an integrated mount and the ability for heat recovery.
If you prefer a tailor-made lighting solution, then eco+ or PRO² might be a better option. These modular systems allow additional control over the arrangement, quantity, and length of individual LED bars. The choice depends on your vision of perfect lighting, whether you opt for the ready-made solution (aquaLUMix) or prefer a customizable system (eco+/PRO²).
|
eco+ |
PRO² |
aquaLUMix A new record in performance, functionality and quality |
---|---|---|---|
LED configuration |
72 LEDs/m |
144 LEDs/m |
340 LEDs/m |
Output |
34W/m |
53W/m |
110W/m |
Lumens |
Up to approx. 3800 lm/m |
Up to approx. 6500 lm/m |
Up to approx. 14000 lm/m |
Efficiency |
Up to 112 lm/W |
Up to 123 lm/W |
Up to 140 lm/W |
Available light colours, variants |
12 |
11 |
4 |
Available lengths |
7 (20-140cm) |
6 (47-135cm) |
7 (24-144cm) |
Cooling |
Passive by |
Passive or |
Passive or Heat recovery (LED water cooling = aquarium heating) |
Design |
Slender, lightweight |
Compact LED bar |
Solid, preconfigured Compact lamp incl. mounting solution |
Cross section |
18x12mm |
32x18mm |
94x28mm |
Max. configuration of |
4x eco+ LED bars in parallel |
2x PRO² LED bars and |
1x aquaLUMix |
Our LED bars are specifically designed to cater to a wide array of needs and applications. Here are the specific possibilities:
eco+ LED bars: An offering of 12 single-color light options, suitable for various environments and requirements.
PRO² LED bars: 2 separately controllable light colors with a total of 8 combinations to choose from, to meet specific lighting needs.
aquaLUMix: Depending on the purpose, there are pre-configured light setups like FRESHWATER, AMAZON-GROW, AFRICAN-SUN, SEAWATER, divided into 4 separately controllable channels.
easyBEAM and flexBEAM: Pre-configured LED combinations as per need, like PLANT-MIX, DAY, SEAWATER, or DEEP BLUE, provide flexibility and convenience.
powerBEAM: Similar to aquaLUMix with pre-configured light setups like AMAZON-GROW, AFRICAN-SUN, SEAWATER, where the main light and white/blue moonlight are separately controllable.
Our light colors, including PLANT-GROW, GROWx5, RED, SUNSET, TROPIC, DAY, SKY, POLAR, REEF, CORAL MIX, MARINE, ROYAL BLUE, are either available as individual LED bars (eco+) or partially as MIX LED bars (PRO²). This range enables promoting optimal growth of plants, enhancing the appearance of aquariums, or creating special light effects like sunrise and sunset.
Based on our extensive experience, we use a mix of these light colors in all other LED lighting solutions to provide the best lighting solution for your specific requirements.
Modul system eco+/PRO²
A convincing daylight simulation can be achieved with 2 light colours, e.g. SUNSET and DAY. Whether to use RED instead of SUNSET for sunrise and sunset is largely a matter of personal taste. The same applies to the actual "daylight". Our customers use everything from TROPIC, through DAY to MARINE.
Because plants and fish exhibit an infinite variety of colour, it is impossible to say what would be a perfect configuration. If it were possible, we would not offer today's 10 different colours ;-) but with this range of colours everyone is able to compose optimum and individual lighting conditions for their aquariums, be they East African, Amazonian, Asian etc.
If you prefer bluish colours, you should consider SKY, POLAR, REEF etc. Whereas, if orange and red colours are preferred or you have luxuriant planting schemes, the light colours SUNSET, TROPIC, DAY would be a good combination. RED and ROYAL BLUE come into play for creating special accents and effects.
Because our customers occasionally become uncertain when faced with such a wide choice, we suggest the following:
with a colour combination of SUNSET, DAY, POLAR (or if preferred TROPIC, DAY, SKY), the colour spectrum is well and broadly covered, which means it is difficult to go wrong. See Light comparison. Our experiences with this composition and planted aquariums have been very good. These light colours are also very suitable for daylight simulation systems. This is our recommended standard configuration.
Whether you choose to have 3 different series of lamps and light colours or restrict yourself to 1-2 depends on your particular aquarium lighting requirements. Depending on your requirements, you can also combine other light colours (RED = dawn reds, ROYAL BLUE = moonlight). Of course, you can add to this very easily at any time in the future. (Assuming the mains adapter has the required capacity)
Compact system aquaLUMix
The question as to the best choice of colour no longer arises with aquaLUMix as, based on years of experience, we've already equipped these compact lights with optimum light combinations. We offer 4 ready-configured lights for freshwater and seawater aquariums in a choice of 5 lengths, from 54 to 144cm. In the case of aquariums of over 144cm in length, two lights are simply combined together.
Depending on the inhabitants and set-up of your aquarium, as well as personal taste, you can choose one of 4 colour combinations - a fitting solution for every area:
- FRESHWATER - Clear, bright colours for outstanding colour rendering, without being detrimental to plant growth. (e.g. for the classic company aquarium)
- AMAZON GROW - A bright, tropical light with a focus on optimum plant growth, including Grow LEDs. (e.g. for thickly-planted Amazon or Asian aquariums)
- AFRICAN SUN - A higher proportion of blue in the daytime light, augmented by a colour-intensifying light composition. (e.g. for cichlid aquarium with Malawis or Tanganyikas)
- SEAWATER - Basically, a high proportion of blue with white and blue light, with additional special colours like red, violet and ultraviolet. (For seawater aquariums)
Every variation of the aquaLUMix is equipped with 4 separately controllable light channels, thus offering incomparable lighting options. Thus, besides light colours for general daytime lighting, LEDs for moonlight and sunrise are also integrated. In addition, a fastener, a splashguard and a water cooling system that can be used if necessary are already included. A suitable mains supply unit and, if desired, a light control or splitter should be ordered separately!
You'll find details on this light and colour configuration in the technical data further down this page.
Moonlight in LED bars is typically the color ROYAL BLUE or alternatively MARINE. The products aquaLUMix, powerBEAM, and spotBEAM already have moonlight integrated, making them particularly suitable for this purpose.
Functions |
SunRiser |
SunRiser |
SunRiser |
SunRiser |
SimuLUX 24 |
---|---|---|---|---|---|
Max. brightness 0-100% freely selectable |
X |
X |
X |
X |
X |
Dim phase duration freely selectable |
X |
X |
X |
X |
X |
Sunrise and sunset |
X |
X |
X |
X |
X |
Moonlight possible |
X |
X |
X |
X |
X |
Natural moon phases |
|
|
|
X |
|
Interruptions or changes to the |
|
|
X |
X |
X |
Weekdays individually programmable |
|
|
X |
X |
X² |
Maintenance function (temporary full |
X |
X |
X |
X |
|
Static weather effects |
|
|
X |
X |
X |
Thunderstorm simulation, lightning |
|
|
|
X |
|
Automatic dynamic effects |
|
|
|
X |
|
Time lapse funtion (quick check) | X | ||||
Individually programmable channels |
2 |
2 |
6 |
8 |
5 |
Characteristics |
|
|
|
|
|
Network-ready |
|
|
|
X |
|
Programming directly on the device |
X |
X |
X |
|
|
Programming using Windows PC |
|
|
|
X |
X³ |
Programming and control through |
|
|
|
X |
|
Interface |
|
|
|
LAN |
USB-C |
Automatic time update through the Internet |
|
|
|
X |
|
Regular software updates |
|
|
|
X |
|
Software languages |
DE, EN |
DE, EN |
DE, EN, FR, NL, IT, PL, SE, DK, ES, CZ |
DE |
DE, EN |
Operating instructions |
DE, EN |
DE, EN |
DE, EN |
DE, EN |
DE, EN, IT, NL, FR |
Settings and time automatically |
X |
X |
X |
X |
X |
Open source software, customer |
|
|
|
X |
|
Output |
|
|
|
|
|
Maximum total output LED 12V |
120W (10A) |
240W (20A) |
240W (20A) |
240W (20A) |
240W (20A) |
Maximum output per channel 12V |
60W (5A) |
120W (10A) |
60W (5A) |
60W (5A) |
48W (4A) |
Maximum total output LED 24V |
240W (10A) | 480W (20A) | 480W (20A) | 480W (20A) | 480W (20A) |
Maximum output per channel 24V | 120W (5A) | 240W (10A) | 120W (5A) | 120W (5A) | 96W (4A) |
Options |
|
|
|
|
|
Temperature sensors |
|
|
|
X |
|
Separate WLAN adapter | X | ||||
Power expandable through High-Power Solution | X | X |
²Requires manual switching between programs| ³MAC/OSX possible with separate software
The cable length for the eco+ and PRO² LED bars is 150cm. In order to extend the cables of the LED bars (150cm), which may be too short (to the installation site of the control unit), I recommend the extension cable by the metre with the solder connectors.
For the aquaLUMix, powerBEAM and multiBEAM products, the cable length is 250cm and should not be extended.
A maximum cable length should always be kept as short as possible. There is a purely physical reason for this: the longer the cable, the higher the voltage drop, the less efficient the lighting. In addition, long cables behave like an antenna; the susceptibility to interference increases massively with the length of the cables. More than 3 m should therefore be avoided if possible.
The cable length of the power supply units is approx. 50cm on the input and output side.
Login
What power output do I need? Please use our calculator to find out:
Power-supply-calculator | ||
---|---|---|
Model | Length/Variant | Quantity |
Power supply Too much for one power supply
|
This is how it works: The power that the mains adapter has to supply is calculated by adding the individual power ratings (watts) of the intended LED lighting bars and then adding a further min. 10% reserve. The correct mains adapter is then the next larger model. Always allow for a minimum 10% power reserve in order not to overload the mains adapter! (Our calculator takes this into account automatically!)
For the avoidance of any misunderstandings: The mains adapters themselves do not consume 30, 75 or 150W of power! But they are capable of delivering this power! Power consumption depends only on the connected LEDs and the efficiency of the mains adapter! In standby (i.e. when the power supply unit is only plugged into the socket, not connected to LEDs or in operation) the consumption is close to zero.
Yes, the LED bars are specifically designed to be installed in existing, enclosed covers. Due to their waterproof rating (IP67), they are suitable for moist aquarium covers but should not be placed directly underwater. Persistent dampness and deposits like lime and dirt may impair the quality and lifespan of the LED bars. Thus, we recommend using our special CleanCover to protect the LED bars. The LED bars cool passively through the ambient air, so adequate air circulation is crucial. In most cases, the existing openings for cables and hoses in the cover are sufficient for this purpose.
The differences between these products depend on your individual lighting needs. The aquaLUMix provides a compact and highly powerful solution with all the light colors needed for an appealing daylight simulation. It also includes an integrated mount and the ability for heat recovery.
If you prefer a tailor-made lighting solution, then eco+ or PRO² might be a better option. These modular systems allow additional control over the arrangement, quantity, and length of individual LED bars. The choice depends on your vision of perfect lighting, whether you opt for the ready-made solution (aquaLUMix) or prefer a customizable system (eco+/PRO²).
|
eco+ |
PRO² |
aquaLUMix A new record in performance, functionality and quality |
---|---|---|---|
LED configuration |
72 LEDs/m |
144 LEDs/m |
340 LEDs/m |
Output |
34W/m |
53W/m |
110W/m |
Lumens |
Up to approx. 3800 lm/m |
Up to approx. 6500 lm/m |
Up to approx. 14000 lm/m |
Efficiency |
Up to 112 lm/W |
Up to 123 lm/W |
Up to 140 lm/W |
Available light colours, variants |
12 |
11 |
4 |
Available lengths |
7 (20-140cm) |
6 (47-135cm) |
7 (24-144cm) |
Cooling |
Passive by |
Passive or |
Passive or Heat recovery (LED water cooling = aquarium heating) |
Design |
Slender, lightweight |
Compact LED bar |
Solid, preconfigured Compact lamp incl. mounting solution |
Cross section |
18x12mm |
32x18mm |
94x28mm |
Max. configuration of |
4x eco+ LED bars in parallel |
2x PRO² LED bars and |
1x aquaLUMix |
Our LED bars are specifically designed to cater to a wide array of needs and applications. Here are the specific possibilities:
eco+ LED bars: An offering of 12 single-color light options, suitable for various environments and requirements.
PRO² LED bars: 2 separately controllable light colors with a total of 8 combinations to choose from, to meet specific lighting needs.
aquaLUMix: Depending on the purpose, there are pre-configured light setups like FRESHWATER, AMAZON-GROW, AFRICAN-SUN, SEAWATER, divided into 4 separately controllable channels.
easyBEAM and flexBEAM: Pre-configured LED combinations as per need, like PLANT-MIX, DAY, SEAWATER, or DEEP BLUE, provide flexibility and convenience.
powerBEAM: Similar to aquaLUMix with pre-configured light setups like AMAZON-GROW, AFRICAN-SUN, SEAWATER, where the main light and white/blue moonlight are separately controllable.
Our light colors, including PLANT-GROW, GROWx5, RED, SUNSET, TROPIC, DAY, SKY, POLAR, REEF, CORAL MIX, MARINE, ROYAL BLUE, are either available as individual LED bars (eco+) or partially as MIX LED bars (PRO²). This range enables promoting optimal growth of plants, enhancing the appearance of aquariums, or creating special light effects like sunrise and sunset.
Based on our extensive experience, we use a mix of these light colors in all other LED lighting solutions to provide the best lighting solution for your specific requirements.
Modul system eco+/PRO²
A convincing daylight simulation can be achieved with 2 light colours, e.g. SUNSET and DAY. Whether to use RED instead of SUNSET for sunrise and sunset is largely a matter of personal taste. The same applies to the actual "daylight". Our customers use everything from TROPIC, through DAY to MARINE.
Because plants and fish exhibit an infinite variety of colour, it is impossible to say what would be a perfect configuration. If it were possible, we would not offer today's 10 different colours ;-) but with this range of colours everyone is able to compose optimum and individual lighting conditions for their aquariums, be they East African, Amazonian, Asian etc.
If you prefer bluish colours, you should consider SKY, POLAR, REEF etc. Whereas, if orange and red colours are preferred or you have luxuriant planting schemes, the light colours SUNSET, TROPIC, DAY would be a good combination. RED and ROYAL BLUE come into play for creating special accents and effects.
Because our customers occasionally become uncertain when faced with such a wide choice, we suggest the following:
with a colour combination of SUNSET, DAY, POLAR (or if preferred TROPIC, DAY, SKY), the colour spectrum is well and broadly covered, which means it is difficult to go wrong. See Light comparison. Our experiences with this composition and planted aquariums have been very good. These light colours are also very suitable for daylight simulation systems. This is our recommended standard configuration.
Whether you choose to have 3 different series of lamps and light colours or restrict yourself to 1-2 depends on your particular aquarium lighting requirements. Depending on your requirements, you can also combine other light colours (RED = dawn reds, ROYAL BLUE = moonlight). Of course, you can add to this very easily at any time in the future. (Assuming the mains adapter has the required capacity)
Compact system aquaLUMix
The question as to the best choice of colour no longer arises with aquaLUMix as, based on years of experience, we've already equipped these compact lights with optimum light combinations. We offer 4 ready-configured lights for freshwater and seawater aquariums in a choice of 5 lengths, from 54 to 144cm. In the case of aquariums of over 144cm in length, two lights are simply combined together.
Depending on the inhabitants and set-up of your aquarium, as well as personal taste, you can choose one of 4 colour combinations - a fitting solution for every area:
- FRESHWATER - Clear, bright colours for outstanding colour rendering, without being detrimental to plant growth. (e.g. for the classic company aquarium)
- AMAZON GROW - A bright, tropical light with a focus on optimum plant growth, including Grow LEDs. (e.g. for thickly-planted Amazon or Asian aquariums)
- AFRICAN SUN - A higher proportion of blue in the daytime light, augmented by a colour-intensifying light composition. (e.g. for cichlid aquarium with Malawis or Tanganyikas)
- SEAWATER - Basically, a high proportion of blue with white and blue light, with additional special colours like red, violet and ultraviolet. (For seawater aquariums)
Every variation of the aquaLUMix is equipped with 4 separately controllable light channels, thus offering incomparable lighting options. Thus, besides light colours for general daytime lighting, LEDs for moonlight and sunrise are also integrated. In addition, a fastener, a splashguard and a water cooling system that can be used if necessary are already included. A suitable mains supply unit and, if desired, a light control or splitter should be ordered separately!
You'll find details on this light and colour configuration in the technical data further down this page.
Moonlight in LED bars is typically the color ROYAL BLUE or alternatively MARINE. The products aquaLUMix, powerBEAM, and spotBEAM already have moonlight integrated, making them particularly suitable for this purpose.
Functions |
SunRiser |
SunRiser |
SunRiser |
SunRiser |
SimuLUX 24 |
---|---|---|---|---|---|
Max. brightness 0-100% freely selectable |
X |
X |
X |
X |
X |
Dim phase duration freely selectable |
X |
X |
X |
X |
X |
Sunrise and sunset |
X |
X |
X |
X |
X |
Moonlight possible |
X |
X |
X |
X |
X |
Natural moon phases |
|
|
|
X |
|
Interruptions or changes to the |
|
|
X |
X |
X |
Weekdays individually programmable |
|
|
X |
X |
X² |
Maintenance function (temporary full |
X |
X |
X |
X |
|
Static weather effects |
|
|
X |
X |
X |
Thunderstorm simulation, lightning |
|
|
|
X |
|
Automatic dynamic effects |
|
|
|
X |
|
Time lapse funtion (quick check) | X | ||||
Individually programmable channels |
2 |
2 |
6 |
8 |
5 |
Characteristics |
|
|
|
|
|
Network-ready |
|
|
|
X |
|
Programming directly on the device |
X |
X |
X |
|
|
Programming using Windows PC |
|
|
|
X |
X³ |
Programming and control through |
|
|
|
X |
|
Interface |
|
|
|
LAN |
USB-C |
Automatic time update through the Internet |
|
|
|
X |
|
Regular software updates |
|
|
|
X |
|
Software languages |
DE, EN |
DE, EN |
DE, EN, FR, NL, IT, PL, SE, DK, ES, CZ |
DE |
DE, EN |
Operating instructions |
DE, EN |
DE, EN |
DE, EN |
DE, EN |
DE, EN, IT, NL, FR |
Settings and time automatically |
X |
X |
X |
X |
X |
Open source software, customer |
|
|
|
X |
|
Output |
|
|
|
|
|
Maximum total output LED 12V |
120W (10A) |
240W (20A) |
240W (20A) |
240W (20A) |
240W (20A) |
Maximum output per channel 12V |
60W (5A) |
120W (10A) |
60W (5A) |
60W (5A) |
48W (4A) |
Maximum total output LED 24V |
240W (10A) | 480W (20A) | 480W (20A) | 480W (20A) | 480W (20A) |
Maximum output per channel 24V | 120W (5A) | 240W (10A) | 120W (5A) | 120W (5A) | 96W (4A) |
Options |
|
|
|
|
|
Temperature sensors |
|
|
|
X |
|
Separate WLAN adapter | X | ||||
Power expandable through High-Power Solution | X | X |
²Requires manual switching between programs| ³MAC/OSX possible with separate software
The cable length for the eco+ and PRO² LED bars is 150cm. In order to extend the cables of the LED bars (150cm), which may be too short (to the installation site of the control unit), I recommend the extension cable by the metre with the solder connectors.
For the aquaLUMix, powerBEAM and multiBEAM products, the cable length is 250cm and should not be extended.
A maximum cable length should always be kept as short as possible. There is a purely physical reason for this: the longer the cable, the higher the voltage drop, the less efficient the lighting. In addition, long cables behave like an antenna; the susceptibility to interference increases massively with the length of the cables. More than 3 m should therefore be avoided if possible.
The cable length of the power supply units is approx. 50cm on the input and output side.