Heat-shrink solder connector for extending connection cables: Connect - solder - insulate - seal - in one simple working process.
€1.69*
Available, delivery time: 1-3 days
Heat-shrink solder connector for extending connection cables:
Connect - solder - insulate - seal - in one simple working process.
Child's play! All done without a soldering iron or solder wire. The result is a watertight and more durable connection than with crimp connectors or screw terminals.
Scope of supply for eco+:
2 No. solder connectors
1 No. heat-shrink hose
Scope of supply for PRO²:
4 No. solder connectors
1 No. heat-shrink hose
Technical data:
Ingress protection type: IP67
Heat-shrink at: >110 C°
Temperature-resistance after shrinking: -45 °C to +125 °C
Length of solder connector: 40mm
Diameter 3mm, for cable cross-sections 0.5-0.75mm²
Instructions: Remove approximately 5 mm of insulation from the cables to be connected. Twist each of the bare cable ends and insert them, one from each side, until the ends lie parallel to one another under the silver ring (solder) in the middle of the connector. Heat the solder connector to approximately 110°C (it is best to use a hot-air gun, but it also can be done with care using a cigarette lighter etc.). The heat shrink sleeve reduces in diameter and sticks together, the solder melts completely and a watertight and very strong connection is produced. Hold the cable in position until the solder has cooled and become solid. The heat-shrink hose is transparent, which allows you to visually inspect the connection. Now shrink-on the supplied black heat-shrink hose around the whole connection for additional protection and to make it so the connection cannot be seen. AND THAT'S IT DONE.
Login
31 August 2021 09:19
Sehr gut
Etwas Geschick erforderlich, aber für technisch nicht ganz Unerfahrene gut leistbar. Es erspart den Lötkolben.
22 December 2017 19:06
super einach zu verarbeiten
21 August 2015 07:28
wie immer TOPPPP
die lötverbinder sind einfach der Hammer
6 January 2021 20:30
Wunderbar
Tolle Sache. Musste mich erst etwas reinfummeln, hat dann aber hervorragend funktioniert.
13 November 2017 09:35
gut
18 December 2015 10:42
Spitze!
Bisher kannte ich solche verbindungen nicht, wenn ich an das blöde Gerödel mit Lötkolben ode Lüsterklemmen zurückdenke.. Einfach Genial, nie wieder Ohne diese Verbinder! Kurz mit Heißluftfön warmmachen, und schon ist super verbunden!
25 August 2023 08:07
Die Verbinder zur Kabelverlängerung sind sehr einfach
Die Verbinder zur Kabelverlängerung sind sehr einfach zu benutzen. Heißluftfön reicht!
3 October 2020 23:38
Hat super geklappt. Hab vorsichtig mit dem Feuerzeug gearbeitet. Alles OK! Eine sehr gute Idee mit dem Lötverbinder.
14 December 2015 18:33
sehr gut
Man kann die Kabel damit sicher und einfach verbinden.
Customers also bought
The CleanCover protects the LED bar from limescale and dirt deposits and is very easy to clean. A splashwater protection, made of highly transparent, ultra-thin, impact-resistant plastic.
For easy bundling and guidance of cable lines.
High-performance LED switching mains adapter for operating our LED lighting bars (12V DC)
Similar products
Heat-shrink solder connector for extending connection cables: Connect - solder - insulate - seal - in one simple working process.
This distributor allows several LED lighting bars to be operated with a single mains adapter (assuming the power output is adequate).
Adapters to connect LED lamps and, if necessary, mains adapters manufactured by third parties to our dimmers, light control and daylight simulation systems.
For connecting 2 LED bars or 2 temperature sensors to one channel of a light control.
Customers also viewed
The CleanCover protects the LED bar from limescale and dirt deposits and is very easy to clean. A splashwater protection, made of highly transparent, ultra-thin, impact-resistant plastic.
The CleanCover protects the LED bar from limescale and dirt deposits and is very easy to clean. A splashwater protection, made of highly transparent, ultra-thin, impact-resistant plastic.
